Do you need a cooker control unit?
How Should an Electric Cooker be Installed? Installing or fitting an electric cooker must be done on its own circuit. An electric cooker cannot be spurred of any other circuit and must be controlled by its own fuse at the consumer unit.
What is a cooker control unit?
A cooker control unit contains both the cooker switch and a cooker socket, which can act as an isolator. A neon light is useful as it acts as a visual that identifies if power is being provided to the cooker.
Where do you put a cooker switch?
The switch or control unit should be readily accessible. It should not be positioned behind or above a cooking appliance such that a person would have to reach over the appliance in order to access the switch/control unit.
Is a cooker switch double pole?
The cooker switch is a double pole switch so is a better means of isolation than the MCB. There is no such requirement in the regulation.
How far should a cooker switch be from a cooker?
‘A minimum distance of 100mm, measured horizontally from an electrical accessory to the edge of a free standing cooker or individual hob is considered acceptable for the purposes of avoiding adverse effects from using a cooker or hob.
Can a cooker switch go in a cupboard?
Answer: It is acceptable to mount a cooker switch in a cupboard, provided that the switch is readily accessible.
Can you plug a cooker into a normal socket?
Save time & money – No hard wiring or electrician needed. Most of the ovens we sell can be plugged into a normal wall socket with a 13a plug and some ovens have a plug already fitted. If you want to check then look for the data badge on the oven and if the total power is less than 3000 watts then it’s fine to plug in.
Are cooker switches needed?
9 Answers from MyBuilder Electricians Regulatory speaking, there is no mandatory requirement for you to have a cooker isolator. Cookers can be wired directly into the distribution board.
Is it OK to leave cooker switch on?
Electricity still runs inside an appliance even if it’s switched off. If electricity is present, there is always the possibility of something overheating or shorting out. However, it is far more likely that if something was to go wrong it would be whilst the appliance is in use.
Can a cooker switch be in a cupboard?
What is the maximum distance between the cooker control unit and the electrical cooker?
In those circumstances it would be up to the installer to decide on a safe and readily accessible alternative location. Some guidance we found recommends a minimum distance from 100mm, however 300mm is the preferred distance up to a maximum distance of 2m and certainly not directly behind the hob.
Can a cooker switch be in another room?
The switch can be put in another room if less than 2 mtres from appliance but must be lockable due to being out of sight completely.
What are the different standards for cooker switches and control units?
The installation of cooker switches or cooker control units is a useful alternative to the electrical installation of a cooking appliance via a plug and socket-outlet. For cooker switches, they must comply with BS EN 60669-2-4 [1], and for cooker control units the applicable standard is BS 4177 [2]. Why the different standards?
Can a cooker switch be used to control two appliances?
A cooker switch/control unit may be used to control two or more cooking appliances in the same room (such as an oven/grill and a separate hob unit), as shown in Fig 1, provided it has sufficient current rating. The switch or control unit should be positioned so that it is accessible and convenient for use.
How high can a cooker switch be above the floor?
Based on the recommendations of Approved Document M, applicable in England and Wales, the height of the switch or control unit should not exceed 1.2 m above floor level (see Fig 2). A cooker switch or control unit should not be installed in a cupboard or cabinet unless it will be accessible and convenient for use.
Can a cooker switch be installed in a cupboard?
A cooker switch or control unit should not be installed in a cupboard or cabinet unless it will be accessible and convenient for use. In any event, wiring and other electrical equipment should not be fixed to any part of a cupboard or cabinet that is demountable in normal use.