How do I point my bell dish to dual LNB?

Posted on by Emilia Duggan

How do I point my bell dish to dual LNB?

The connection between the LNB and the receiver must be direct (meaning no switches or splitters). On the TV, set the satellite to 91 and the transponder to 1. If you don’t know how to get to this screen, press Menu and then numbers 6, 1, 1 on your receiver remote. Now you are ready to point the satellite.

What is a dual tuner satellite receiver?

Your 9242 dual-tuner satellite receiver lets you watch programming on two separate TVs. The way this programming is delivered changes depending on whether the receiver is set to Single or Dual Mode.

How do I install bell 91 and 82?

With SW21, all you need to do is input one cable from the LNB that captures 91° satellite and input another cable from the LNB that captures 82°(see image below). The output of the SW21 switch will connect to the receiver and you will be ready to receive signal from both satellites using this setup.

How do I install a second bell satellite receiver?

Activate the receiver and SmartCard in MyBell….Note: Make sure you have the 4-digit PIN for your Bell Satellite TV account handy.

  1. Call 1 866 353-03341 866 353-0334.
  2. Choose the Activate an additional receiver option from the self-serve prompts.
  3. Follow the instructions.

How do I connect my bell 6400 receiver?

6400 – HD receiver

  1. Disconnect your old receiver and connect the replacement using the same cables.
  2. Turn your receiver and TV on.
  3. Wait about 2 to 4 minutes until the Point Dish screen is displayed.
  4. Select Check Switch with your Bell TV remote.
  5. Select Test.
  6. Wait about 1 to 5 minutes until the receiver completes the test.

How does a dual LNB work?

Dual LNB connections operate independently of each other, so you can use two receivers. A dual LNB can access different channels on different transponders, but you must install a multi-switch to split the signal.

How do I setup my bell 6400 receiver?

How do I install my bell 9241 receiver?

9241 – HD PVR Plus

  1. Disconnect your old receiver and connect the replacement using the same cables.
  2. Turn your receiver and TV on.
  3. Wait about 2 to 4 minutes until the Point Dish screen is displayed.
  4. Select Check Switch with your Bell TV remote.
  5. Select Test.
  6. Wait about 1 to 5 minutes until the receiver completes the test.

How do I connect my satellite receiver to two TVs?

How to Connect Two TVs to One Satellite Box

  1. Run two 2150 MHz RG6 cables out of your satellite dish.
  2. Hook one end of a 2150 MHz RG6 cable into the “TV 3/4 OUT” connector on your satellite receiver.
  3. Connect another coaxial cable to the receiver’s “CH 21-69 OUT” output.

How do I connect my bell remote to my receiver?

  1. Press SYS INFO on the front of the receiver.
  2. Press and hold SAT until SAT, TV, AUX and VCR light up.
  3. Release SAT. It will start to flash.
  4. Choose a random number between 0 and 16 and enter it. This will reset the frequency the remote uses to communicate with the receiver.
  5. Press #.
  6. Press Record.
  7. Press Done.

What is the HD PVR plus receiver number for Bell TV?

9242 HD PVR Plus Receiver : Get the user guide and support information for your Bell TV equipment. Skip to main content Personal Small Business Medium & Large Business Bell for Better Bell email Bell Stores

Do you do custom installs for Bell TV customers?

I have done numerous custom installs for Bell TV customers who only had single cable runs to there rooms and had multiple dual tuner receivers in there home. So lets jump right in!

Can a bell 9241 HD PVR be used on a SW44 switch?

I resently set up a new Bell 9241 HD PVR in my system. Along with that I currently have a 9200 HD PVR using 2 of the outputs [for the dual tuners] on a legacy SW44 switch. I have 2 Dual LNBs coming off of the Dish feeding 4 lines into the SW44 switch. The SW44 switch is working fine with the 9200 and able to pick up both satellites.

Can a dual tuners receiver be hooked up using only one tuner?

First commonly asked question about Dual Tuners Receiver’s by many is if it can be hooked up using only one of the tuners. The answer to that is NO! If you try to do so, you will run into problems, such as events not recording loss of Tuner 2 functionality.